Installation method of Lauffer laminating machine

2018-01-25 15:52

Shenzhen weixinda industry and trade co., LTD. Introduce youLauffer laminating machineProcess and method of installation.

I. Lifting of Lauffer Laminating Machine
Available car crane (capacity of 20-25 tons or more) hoisting Lauffer laminator. The lifting point of the wire rope shall be set at the bottom of the cubic tube with two fixed guide rails in the middle. The contact surface between the machine and the wire rope shall be isolated by rubber plate or thick paper shell to prevent the surface damage of the machine. Lift the machine to about 50cm above the ground, not too high.
II. Movement of Lauffer Laminator
1. Carefully and slowly drop the raised machine onto the 4 roller groups on a flat ground. Make sure that each vertex of the four corners of the machine is closely matched to the corresponding roller set.
2. As a precaution, place a soft pad between the machine and the rollers.
3. Drop the rope and remove it from the machine.
4. Fix the rope on the machine and move the machine to the installation position with a forklift or winch (fixed at a stable place).
5. Use a fixed crane or jack of more than 10 tons to remove the rollers one by one, and finally install the machine in place.
Three. Roller group requirements
1. Bearing weight:>4 tons/only
2. Ensure that after the machine is jacking up, the rolling direction of the roller can be easily changed
3. Roller set shall be suitable for concrete ground

Previous Page

Vacuum hot press

Requirements of LAUFFER Laminator for Kraft Paper

Next Page

Previous Page

Vacuum hot press

Next Page

Requirements of LAUFFER Laminator for Kraft Paper

More news

Jiangsu Shengyi High Frequency Communication Substrate Project Foundation Laying Ceremony Held

Jiangsu Shengyi High Frequency Communication Substrate Project Foundation Laying Ceremony Held

On the morning of December 17, 2017, the groundbreaking ceremony of Jiangsu Shengyi Special Materials Co., Ltd., invested by Guangdong Shengyi Technology Co., Ltd., was held in Nantong Tongzhou National High-tech Development Zone, which is known as "the first state of Tongjiang and Dahai. Liu Shufeng, chairman of Guangdong Shengyi Technology Co., Ltd., Chen Renxi, general manager, Wu Xiaolian, chief operating officer, Zeng Xutang, chairman of Shaanxi Shengyi Technology Co., Ltd., Yang Hui, general manager, Jiao Feng, general manager of Suzhou Shengyi Technology Co., Ltd., Wang Hui, general manager of Changshu Shengyi Technology Co., Ltd., and representatives of the design, supervision, cost and construction units responsible for project construction attended the ceremony.

2024/03/01

LAUFFER high-frequency board press: high-frequency high-speed substrates will usher in high-speed growth in the 5G era.

LAUFFER high-frequency board press: high-frequency high-speed substrates will usher in high-speed growth in the 5G era.

LAUFFER high-frequency board press collects relevant information of 5G high-frequency and high-speed substrates for you on the Internet.

2024/03/01

Jiangxi Jiujiang PCB Project Formed a Complete Industrial Chain

Jiangxi Jiujiang PCB Project Formed a Complete Industrial Chain

In 2017, Jiangxi Jiujiang Economic Development Zone always regarded investment promotion as the "lifeline" of accelerating development, further innovated the investment promotion system and mechanism, changed the investment promotion thinking, adhered to the "two-wheel drive" to promote development, focused on industrial introduction projects, and achieved a detonating effect New breakthroughs in the recruitment of emerging industries. In the whole year, 73 new industrial projects were signed, with a total investment of 63 billion billion yuan, and the proportion of strategic emerging industry projects increased by 37%. In the electronic circuit materials industry, the development zone mainly focuses on Taiwan-funded Dehong fine yarn and the world's second-largest Shengyi copper clad laminate project, resulting in investment in 3 billion yuan Dehong glass fiber yarn and electronic cloth project,

2024/03/01