The plate of the process flow of the vacuum laminator.

2021-11-02 09:33

Before using the vacuum laminator for production, the plates shall be arranged first, the first layer shall be arranged for each Book, the bottom steel plate shall be fixed, the plate arrangement range shall be marked on the bottom steel plate, and then the other layers shall be arranged according to the marking position and the tin injection alignment system.

 

The board arranging staff shall follow the principle of holding the board with both hands, handling it with care, and spot check whether there is brownish layer wiping flowers on the board surface. If there are serious batches of flowers, notify the foreman or supervisor to deal with them. When producing more than six boards, each row-BOOK should check whether a pre-row board is correct, and the required number of rows must be clear. Make sure to install anti-skid fixture after each BOOK board is arranged. For each row-furnace board, according to the order of the row board, fill in the laminated row board and press board record form and the original production record form of the process post, fill in the material model and material batch number on the process card, and then hand over the process card to the board staff. Sweep the upper copper box twice in the same way. The wax cloth strips shall be replaced at the specified frequency.

Put steel plates and core plates, and cars with P plates should be arranged neatly and not skewed. Do not use sandpaper to polish the steel plate in the board row room. If the steel plate is found to be abnormal, move it out to the board row room for polishing and cleaning. Each row of one furnace plate, according to the order of plate discharge, fill in the laminated plate discharge and pressure plate record form and fill in the material model and material batch number on the process card, process card to the pressure plate staff.
 

Previous Page

HDI Pressing of Vacuum Laminator

Germany lauffer hot press why quality is so good?

Next Page

Previous Page

HDI Pressing of Vacuum Laminator

Next Page

Germany lauffer hot press why quality is so good?

More news

Jiangsu Shengyi High Frequency Communication Substrate Project Foundation Laying Ceremony Held

Jiangsu Shengyi High Frequency Communication Substrate Project Foundation Laying Ceremony Held

On the morning of December 17, 2017, the groundbreaking ceremony of Jiangsu Shengyi Special Materials Co., Ltd., invested by Guangdong Shengyi Technology Co., Ltd., was held in Nantong Tongzhou National High-tech Development Zone, which is known as "the first state of Tongjiang and Dahai. Liu Shufeng, chairman of Guangdong Shengyi Technology Co., Ltd., Chen Renxi, general manager, Wu Xiaolian, chief operating officer, Zeng Xutang, chairman of Shaanxi Shengyi Technology Co., Ltd., Yang Hui, general manager, Jiao Feng, general manager of Suzhou Shengyi Technology Co., Ltd., Wang Hui, general manager of Changshu Shengyi Technology Co., Ltd., and representatives of the design, supervision, cost and construction units responsible for project construction attended the ceremony.

2024/03/01

LAUFFER high-frequency board press: high-frequency high-speed substrates will usher in high-speed growth in the 5G era.

LAUFFER high-frequency board press: high-frequency high-speed substrates will usher in high-speed growth in the 5G era.

LAUFFER high-frequency board press collects relevant information of 5G high-frequency and high-speed substrates for you on the Internet.

2024/03/01

Jiangxi Jiujiang PCB Project Formed a Complete Industrial Chain

Jiangxi Jiujiang PCB Project Formed a Complete Industrial Chain

In 2017, Jiangxi Jiujiang Economic Development Zone always regarded investment promotion as the "lifeline" of accelerating development, further innovated the investment promotion system and mechanism, changed the investment promotion thinking, adhered to the "two-wheel drive" to promote development, focused on industrial introduction projects, and achieved a detonating effect New breakthroughs in the recruitment of emerging industries. In the whole year, 73 new industrial projects were signed, with a total investment of 63 billion billion yuan, and the proportion of strategic emerging industry projects increased by 37%. In the electronic circuit materials industry, the development zone mainly focuses on Taiwan-funded Dehong fine yarn and the world's second-largest Shengyi copper clad laminate project, resulting in investment in 3 billion yuan Dehong glass fiber yarn and electronic cloth project,

2024/03/01