Software Operation of Lauffer Laminator System

2022-07-13 10:44

Lauffer laminator turns on the power of the computer after turning on the control button of the system operation of the computer control table. at this time, the ml software dedicated to the pressing system runs automatically.

After the ML software runs automatically, the view of the software presents the site distribution map of the entire Lauffer pressing system and the names of each part. According to the diagram, look at the state of its parts State):

1. In operation (Cycle running) and the period of this pressing program (Cycle time) and the active operation time (Act cycle time), unit: minutes.

2. There is no operation (No operation), and the cycle (Cycle time) and run time (Act Cycle time)0 (unit: minutes) of the last running program are displayed at the same time.

3. According to the signs provided in the figure, see whether each part is automatic or manual.

4. One of the entry system is in manual state, and the "Manual button (Manual)" in the lower left corner of the figure is the precautions and inspection items before the blue automatic pressing plate:

A. at this time, we can see the operation mode of each part: automatic mode/manual mode (the manual mode Manualoperation is blue, while the Manual button in the lower left corner of the total picture View is blue, otherwise, automatic mode).

B. running state (State) of hot press 1/2 and cold press: no load (No operation is red), and the last running time of the press (Cycle time unit is minutes min); During operation (Cycle running is green), the total time of the pressing program (Cycle time unit is minutes min) and the actual pressing program has been running (Actual time).

C. the state of the control sensor (Light beam) of the hot press, cold press, feed rack and discharge rack: the normal state is green (Light beam free) and the abnormal state is red (light beam interrupt).

D. display the current number of alarms in the lower alarm bar of the general view: if there is an alarm, double-click the number bar to view the alarm content and eliminate the alarm; You can also view it in the "Introduction (Info)" at the top of the view.

Previous Page

Types and heating methods of PCB press

Market Status of PCB Laminating Machine

Next Page

Previous Page

Types and heating methods of PCB press

Next Page

Market Status of PCB Laminating Machine

More news

Jiangsu Shengyi High Frequency Communication Substrate Project Foundation Laying Ceremony Held

Jiangsu Shengyi High Frequency Communication Substrate Project Foundation Laying Ceremony Held

On the morning of December 17, 2017, the groundbreaking ceremony of Jiangsu Shengyi Special Materials Co., Ltd., invested by Guangdong Shengyi Technology Co., Ltd., was held in Nantong Tongzhou National High-tech Development Zone, which is known as "the first state of Tongjiang and Dahai. Liu Shufeng, chairman of Guangdong Shengyi Technology Co., Ltd., Chen Renxi, general manager, Wu Xiaolian, chief operating officer, Zeng Xutang, chairman of Shaanxi Shengyi Technology Co., Ltd., Yang Hui, general manager, Jiao Feng, general manager of Suzhou Shengyi Technology Co., Ltd., Wang Hui, general manager of Changshu Shengyi Technology Co., Ltd., and representatives of the design, supervision, cost and construction units responsible for project construction attended the ceremony.

2024/03/01

LAUFFER high-frequency board press: high-frequency high-speed substrates will usher in high-speed growth in the 5G era.

LAUFFER high-frequency board press: high-frequency high-speed substrates will usher in high-speed growth in the 5G era.

LAUFFER high-frequency board press collects relevant information of 5G high-frequency and high-speed substrates for you on the Internet.

2024/03/01

Jiangxi Jiujiang PCB Project Formed a Complete Industrial Chain

Jiangxi Jiujiang PCB Project Formed a Complete Industrial Chain

In 2017, Jiangxi Jiujiang Economic Development Zone always regarded investment promotion as the "lifeline" of accelerating development, further innovated the investment promotion system and mechanism, changed the investment promotion thinking, adhered to the "two-wheel drive" to promote development, focused on industrial introduction projects, and achieved a detonating effect New breakthroughs in the recruitment of emerging industries. In the whole year, 73 new industrial projects were signed, with a total investment of 63 billion billion yuan, and the proportion of strategic emerging industry projects increased by 37%. In the electronic circuit materials industry, the development zone mainly focuses on Taiwan-funded Dehong fine yarn and the world's second-largest Shengyi copper clad laminate project, resulting in investment in 3 billion yuan Dehong glass fiber yarn and electronic cloth project,

2024/03/01