Laboratory Laminator Temperature Control Failure Reason

2024-01-05 14:05

In the use of laboratory laminators and hot presses, temperature control failure may be a common fault condition. The failure of temperature control will cause the hot press to fail to reach the required temperature stably, which will affect the accuracy and reliability of the experimental results. Temperature control failure may have a variety of reasons, including sensor damage, controller failure, circuit connection problems, etc. When the failure of temperature control is found, troubleshooting and analysis are first needed to determine the specific cause of the failure. The problem of temperature control failure can be solved by the following steps:

 

1. Check the temperature sensor: First, check whether the temperature sensor is damaged or there is a connection problem. A preliminary judgment can be made by checking the appearance of the sensor for obvious damage or looseness. If there is a problem, the sensor needs to be replaced or reconnected.

2. Check the controller: If the sensor is working normally, but the temperature control still fails, it may be caused by a controller failure. You can try to reset the parameters of the controller, or replace the controller to solve the problem.

3. Check the circuit connection: the normal operation of the temperature control system also depends on the connection of the circuit. Therefore, it is necessary to check the circuit for loose, open circuit or other connection problems. If a problem is found, it is necessary to repair the circuit connection or replace the faulty circuit component.

4. System test: After eliminating the above possible reasons, the system test of the hot press is required to confirm whether the temperature control problem has been solved. You can set a stable target temperature and observe whether the hot press can accurately control the temperature to reach the target.

 

Through the above steps, the problem of temperature control failure of laboratory laminator and hot press can be solved more comprehensively. However, in the process of maintenance, it is necessary to pay attention to safety matters to avoid injury to laboratory equipment and personnel. If the problem cannot be solved by itself, it is recommended to seek professional help to ensure that the laboratory heat press can work normally.

Previous Page

Relationship between PCB Lamination Quality Problem and Copper Clad Laminate

Introduction of the characteristics of vacuum laminating machine

Next Page

Previous Page

Relationship between PCB Lamination Quality Problem and Copper Clad Laminate

Next Page

Introduction of the characteristics of vacuum laminating machine

More news

Jiangsu Shengyi High Frequency Communication Substrate Project Foundation Laying Ceremony Held

Jiangsu Shengyi High Frequency Communication Substrate Project Foundation Laying Ceremony Held

On the morning of December 17, 2017, the groundbreaking ceremony of Jiangsu Shengyi Special Materials Co., Ltd., invested by Guangdong Shengyi Technology Co., Ltd., was held in Nantong Tongzhou National High-tech Development Zone, which is known as "the first state of Tongjiang and Dahai. Liu Shufeng, chairman of Guangdong Shengyi Technology Co., Ltd., Chen Renxi, general manager, Wu Xiaolian, chief operating officer, Zeng Xutang, chairman of Shaanxi Shengyi Technology Co., Ltd., Yang Hui, general manager, Jiao Feng, general manager of Suzhou Shengyi Technology Co., Ltd., Wang Hui, general manager of Changshu Shengyi Technology Co., Ltd., and representatives of the design, supervision, cost and construction units responsible for project construction attended the ceremony.

2024/03/01

LAUFFER high-frequency board press: high-frequency high-speed substrates will usher in high-speed growth in the 5G era.

LAUFFER high-frequency board press: high-frequency high-speed substrates will usher in high-speed growth in the 5G era.

LAUFFER high-frequency board press collects relevant information of 5G high-frequency and high-speed substrates for you on the Internet.

2024/03/01

Jiangxi Jiujiang PCB Project Formed a Complete Industrial Chain

Jiangxi Jiujiang PCB Project Formed a Complete Industrial Chain

In 2017, Jiangxi Jiujiang Economic Development Zone always regarded investment promotion as the "lifeline" of accelerating development, further innovated the investment promotion system and mechanism, changed the investment promotion thinking, adhered to the "two-wheel drive" to promote development, focused on industrial introduction projects, and achieved a detonating effect New breakthroughs in the recruitment of emerging industries. In the whole year, 73 new industrial projects were signed, with a total investment of 63 billion billion yuan, and the proportion of strategic emerging industry projects increased by 37%. In the electronic circuit materials industry, the development zone mainly focuses on Taiwan-funded Dehong fine yarn and the world's second-largest Shengyi copper clad laminate project, resulting in investment in 3 billion yuan Dehong glass fiber yarn and electronic cloth project,

2024/03/01